收藏本站
SX1210
ADVANCED COMMUNICATIONS & SENSING
FSK mode: The 99% energy bandwidth of an FSK modulated signal is approximated to be:
BW 99 %, FSK = 2 * ? Fdev +
?
?
BR ?
2 ??
The bits RXParam_ButterFilt set fc, the cutoff frequency of the filter. As we are in a Zero-IF configuration, the FSK
lobes are centered around the virtual “DC” frequency. The choice of fc should be such that the modulated signal
falls in the filter bandwidth, anticipating the Local Oscillator frequency drift over the operating temperature and
aging of the device:
2 * fc > BW 99 %, FSK + LO drifts
Please refer to the charts in section 3.3.5 for an accurate overview of the filter bandwidth vs. setting.
OOK mode: The 99% energy bandwidth of an OOK modulated signal is approximated to be:
BW 99 %, OOK =
2
Tbit
= 2 . BR
The bits RXParam_PolypFilt_center set fo, the center frequency of the polyphase filter when activated. fo should
always be chosen to be equal to the low Intermediate Frequency of the receiver (IF2). This is why, in the GUI
described in section 7.2.1 of this document, the low IF frequency of the OOK receiver denoted IF2 has been
replaced by fo.
The following setting is recommended:
fo = 100 kHz
RXParam _ PolypFilt = " 0011 "
The value stored in RXParam_ButterFilt determines fc, the filter cut-off frequency. So the user should set fc
according to:
2 * ( fc ? fo ) > BW 99 %, OOK + LO drifts
Again, fc as a function of RXParam_ButterFilt is given in the section 3.3.6.
3.3.5. Channel Filters Setting in FSK Mode
Fc, the 3dB cutoff frequency of the Butterworth filter used in FSK reception, is programmed through the bit
RXParam_ButterFilt. However, the whole receiver chain influences this cutoff frequency. Thus the channel select
and resultant filter bandwidths are summarized in the following chart:
Rev 2– Sept 8 , 2008
th
Page 19 of 73
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SX1211SK915 KIT STARTER FOR SX1211 915MHZ
SX1211SKA915 KIT STARTER FOR SX1211 915MHZ
SX1223SK868 KIT STARTER FOR XE1223 868MHZ
SX1231-31SKB915 TVS
SX1240SKA433 TVS
SX1701BI085TRT IC AMP 2.5GHZ 5.3V 16-MLPQ
TA002-10002 LED HEATSINK W/FAN 12V 40X10MM
TC620HEPA IC TEMP SNSR 5V DUAL TRIP 8-DIP
相关代理商/技术参数
SX1210I084TRT 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:IC SINGLE-CHIP RECEIVER 32-TQFN 制造商:Semtech Corporation 功能描述:SX1210 Series 863 to 960 MHz 3 V 200 kbps Ultra Low Power Receiver - TQFN-32
SX1211 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Lowest Power Integrated UHF Transceiver Short Range Devices
SX1211_08 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated UHF Transceiver
SX1211-11SKA868 功能描述:KIT STARTER FOR SX1211 868MHZ RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
SX1211-11SKA915 功能描述:KIT USB FOR SX1211 TXRX 915MHZ RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
SX1211I084T 制造商:Semtech Corporation 功能描述:
SX1211I084TRT 功能描述:IC SNGL-CHIP TXRX 32-TQFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件
SX1211I084TRT 制造商:Semtech Corporation 功能描述:GPSS WL SKU APP1